ATMSIGD.CONF(4)

NAME
atmsigd.conf - configuration file for the ATM signaling demon

SYNOPSIS
/etc/atmsigd.conf

DESCRIPTION
atmsigd.conf contains configuration data for atmsigd. atmsigd reads atmsigd.conf after parsing the command line options, before connecting to the ATM network.

Configuration parameters are arranged in functional groups. In order to set a parameter, the name of the group, the name of the parameter, and the parameter value(s) have to be specified, e.g.

     sig level debug

decreases the logging threshold for messages related to signaling to the debug level. The following options are recognized:

debug dump path
    Specifies the directory to which atmsigd will write status and trace dumps. If tracing is not yet enabled, the trace size is automatically set to a (small) default value.

debug level level
    Sets the default debug level to level. level can be any of debug, info, warn, error, and fatal. Only messages with the same or a higher priority than the debug level are printed. Note that the command-line option -d generates even more output (e.g. hexdumps of all packets passing between atmsigd and the network) than debug level debug.

debug log path
    Specifies the file to which atmsigd writes logging messages. When using the special file name syslog, messages are send to the system logger instead. Log messages are written to standard output if no log file is specified. Writing to standard output can also be explicitly requested by using the special file name stderr.

debug trace [number]
    Enables tracing and optionally sets the number of entries that should be kept in the trace buffer. A (small) default is used if the number is omitted.

io level level
    Sets the debug level for IO-related messages to level.

io max_rate rate
    Sets the rate to signal if an application requests the "maximum". See qos(7) for the syntax to use for expressing the rate. The default maximum rate is 353207 cells/second (OC3). (Note that the value of max_rate does not constrain the rates an application can explicitly request.)

io qos qos
    Configures the signaling VC to use the specified QOS (see qos(7) for the syntax). By default, UBR at link speed is used on the signaling VC.

io vc [itf.]vpi.vci
    Uses the specified VC for signaling messages instead of the usual 0.0.5.

saal level level
    Sets the debug level for messages related to SAAL (i.e. SSCF and SSCOP) to level.

sig level level
    Sets the debug level for messages related to signaling (Q.2931 or ISP) to level.

sig mode mode
    Set the mode of operation. The following modes are available: user for the user side, network for the network side, and switch for operation in a switch. The default behaviour is user.

sig uni30
    Use UNI 3.0 signaling. If specified together with sig uni31, this option sets UNI 3.1 signaling with a few backwards-compatibility extensions.

sig uni31
    Use UNI 3.1 signaling. This option can be combined with sig uni30 (see above).

sig uni40
    Use UNI 4.0 signaling. This option can be combined with sig q.2963.1 (see below).

sig q.2963.1
    Enable peak cell rate renegotiation. This option is only available with UNI 4.0 signaling.

sig vpci vpci itf itf
    Sets up a very simplistic type of routing. All calls with VPCI values equal to or greater than vpci will be routed to itf, and their VPI values will be set to the signaled VPCI minus vpci. Multiple sig vpci entries can be used to support an arbitrary number of interfaces. Example: with sig vpci 4 itf 1, a call signaled for VPCI/VCI 0.x is routed to 0.0.x, a call signaled for 6.y is routed to 1.2.y, etc.

policy level level
    Sets the debug level for messages related to policy decisions to level.

policy decision direction address
    Takes the specified decision for calls from or to address. decision can be either allow or reject. direction is either from or to. The address may be wildcarded by prepending a slash and the number of significant bits (NSAP) or digits (E.164). The rules are searched in the order in which they appear in atmsigd.conf until the first match. If no rule matches, the call is allowed.

entity [itf.]vpi.vci { options ... }
    Activates a signaling entity on that specific VC. Multiple entity clauses can appear in the same configuration. When using entity, the option io vc is not available. entity is optionally followed by the following options, enclosed in curly braces: vpci (corresponds to sig vpci), mode (corresponds to sig mode), qos (corresponds to vc qos), route, and default. The last two options determine how outbound calls are routed. The route option is followed by an address in the format used for addresses in policy. If no route entry matches the called party number of an outbound call, the entry marked with default is selected.

When setting multiple parameters in the same group, the group name doesn't have to be repeated if it is followed by the parameters in curly braces. Example:

    debug {
        level warn
        dump /var/tmp
        log syslog
        trace 100
    }

Line breaks can be inserted in atmsigd.conf wherever spaces or tabs are allowed. Everything between a `#' and the end of the line is considered a comment. The `#' character cannot be escaped.

If an option is specified in atmsigd.conf and on the command line, the command line has priority.

COMPATIBILITY
Certain options used by past versions of atmsigd but no longer documented on the man page are still recognized and supported, but they also yield a warning message. Future versions of atmsigd will not recognize those options.

AUTHOR
Werner Almesberger, EPFL ICA <Werner.Almesberger@epfl.ch>

SEE ALSO
atmsigd(8), qos(7), syslogd(8)